Piso WiFi

10.0.0.0.1 - Piso WiFi Admin Login, Pause Time & Troubleshooting

 ·  Piso WiFi
10.0.0.0.1 - Piso WiFi Admin Login, Pause Time & Troubleshooting

10.0.0.0.1 is the built-in admin address for most Piso WiFi vending machines sold in the Philippines. You open it in your browser to access the control panel - to set pause time, view active sessions, change the password or configure pricing.

Type `http://10.0.0.0.1` directly into your browser's address bar. Use `admin` as both username and password. If the page does not load, make sure you are connected to the Piso WiFi machine's network, not your home router.

How to Open the 10.0.0.0.1 Admin Panel

Follow these four steps exactly:

  1. Connect to the Piso WiFi network. On your phone or laptop, go to WiFi settings and connect to the network broadcast by the machine. Do not use mobile data - the address only works over the local network.
  2. Open your browser. Chrome, Firefox and Safari all work. Do not use the search bar - use the address bar at the top.
  3. Type the address. Enter `http://10.0.0.0.1` exactly as shown. If your browser adds `https://` automatically and the page fails to load, remove the `s` and try again. This address uses HTTP, not HTTPS.
  4. Log in. Enter `admin` as username and `admin` as password. Most LPB Piso WiFi machines ship with these defaults. If they do not work, the sticker on the back of the machine shows the correct credentials.
If the login page appears but your password is rejected, someone changed the credentials during setup. A factory reset (hold reset button 10 seconds) brings back the defaults.

Default Login Credentials for 10.0.0.0.1

FieldDefault Value
IP Address10.0.0.0.1
Usernameadmin
Passwordadmin
ProtocolHTTP (not HTTPS)
Port80 (default, no need to type)

How to Set Piso WiFi Pause Time

Pause Time lets your customers pause their session and resume it later without losing their remaining credit. This is one of the most-used features and a key reason operators access 10.0.0.0.1 regularly.

After logging in, look for Time Settings, Session Management or Pause Time in the navigation. The exact label depends on your firmware version. Set the maximum pause duration per session - common values are 30 minutes or 1 hour. Save your changes.

If you cannot find the Pause Time option, your machine may be running older firmware. Contact your Piso WiFi supplier for an update.

What to Do When 10.0.0.0.1 Does Not Load

Three causes cover almost every case:

Wrong network. Your device is still connected to your home router or mobile data. Switch to the Piso WiFi machine's WiFi network first.

HTTPS redirect. Some browsers automatically add `https://` to any address you type. The Piso WiFi admin panel does not support HTTPS. Type `http://10.0.0.0.1` with the `http://` prefix to force plain HTTP.

Wrong address. Some machines use `10.0.0.1` instead of `10.0.0.0.1`. Try both. See the 10.0.0.1 guide if the second address is yours.

Frequently Asked Questions

Why can't I open 10.0.0.0.1?

You must be connected to the Piso WiFi machine's own WiFi network. Type the address into the browser's address bar, not Google.

What is the default password for 10.0.0.0.1?

Username: `admin` - Password: `admin`. If that fails, check the sticker on the back of the machine.

Is 10.0.0.0.1 the same as 10.0.0.1?

No. These are different addresses. LPB Piso WiFi and most newer machines use 10.0.0.0.1. Older units often use 10.0.0.1. Try both.

How do I reset the machine to factory defaults?

Hold the reset button for 10 seconds until the lights blink. This restores admin/admin and clears all settings.

Can I access 10.0.0.0.1 from my phone?

Yes. Connect to the Piso WiFi network via WiFi (not mobile data), open Chrome or Safari, and type `http://10.0.0.0.1` into the address bar.